Specifiche
| CPU Support | - Support Dual-Core Intel® Xeon® processor 5100 series and Quad-Core Intel® Xeon® Processor 5300 series (80W)
- Intel® Embedded Processor List ( Intel® Longevity CPU): Dual-Core Intel® Xeon® Processor (5130 & 5140)Dual-Core Intel® Xeon® Processor LV (5128, 5138, 5148)
- 1066/1333 MHz FSB support
|
| Main Memory | - 4 x 240-pin four channel DDR 2 FB-DIMM
- Support ECC/Register DDR2 memory up to 8GB
|
| Chipset | - Intel® 5000P memory controller Hub
- Intel® 6321ESB I/O controller Hub
|
| BIOS | - AMI BIOS
- Plug & Play support
- Support Soft off, Wake on LAN, Power On by PS2 Keyboard Function Key, RTC alarm Power On
- Power on after power failure
- 8M-bit fl ash ROM
|
| On-board LAN | - 2 x Intel® 82573L PCI Express Gigabit Ethernet
- Support Boot From LAN (PXE)
- Support Wake On LAN (When 5Vsb power available)
- 2 x RJ45 with LED
|
| Display | - ATI ES1000 PCI graphic Controller
- 32MB DDR2 SDRAM VGA Memory
- 1 x DB15 VGA port
|
| I/O Interface | - USB 2.0: 4 ports through I/O bracket
- USB 2.0: 2 ports, with 1x6 JST (2.5mm )
- Serial port: 2 ports, with 2x5 box-header (2.0mm) support RS-232 only
- Parallel port: 1 port , with 2x13 box-header (2.0mm), Bi-directional, EPP/ECP
- PS/2: 1 x Mini-Din Keyboard/Mouse
- GPIO: Support 4 sets of general purpose I/O each with TTL level (5V) interface
- FAN: 2 x 4-pin FAN connectors (for CPU coolers)
- 1 x on board buzzer
- 1 x 2-pin power on switch / 1 x SMBus 2.0 to Backplane
- 1 x 2-pin header for reset / 1 x 5-pin header for key lock
- 1 x 2-pin header for power LED / 1 x 2-pin header for HDD LED
|
| Watchdog Timer | - Watchdog Timer is programmable by software from 0 to 255 seconds (Tolerance 10% under room temperature 25°C)
|
| Storage | - SATA: 2 ports, support RAID 0,1 through Backplane
- IDE: 1 x 40-pin IDE connector, support Ultra ATA 33/66/100
- 1 x 2-pin JST (2.5mm) power connector for DOM (Disk On Module)
|
| System Monitor | - 8 voltage (For +3.3V, +5V, Vcore x2, 1.8V, 1.5V, 5Vsb, and Vbattery)
- 3 temperature (For 2 CPU and system)
- 3 FAN speed monitor ( 2 for CPU and 1 for ESB2)
|
| On-board RTC | - On-chip RTC with battery back up
- 1 x External Li-Lon battery
|
| Dimensions | - PICMG 1.3 SHB, 338.58 mm (L) x 126.39 mm (W) (13.3" x 4.9")
|
| Power Input | - Power source from backplane through PICMG 1.3 Golden Finger, support ATX mode-- CPU:2 x Dual-Core Xeon 3.0G, Memory:4 x FBD DDR2 2.0GB:+12V +5V +3.3V +5Vsb; Full-Loading Mode:21.4A 2.07A 3.85A 0.04A; Light-Loading Mode:10.59A 1.69A 3.63A 0.04A. (NOTE: 1.Full Loading: Utilize CPU 100% with Burn-in test running 2.Light Loading: Utilize CPU loading below 5% without data or application running)
|
| Environment | - Operating Temperature: 0°C ~ 60°C (for Board Level Only)
- Storage Temperature: -20˚C to 85˚C
- Relative Humidity: Operating: 10%~90% (non-condensing), Non-Operating: 5%~95% (non-condensing)
|
| Certifications | |